Fault code in 2007 International 128 F04 PID 175_A, 2007. 1-5 Months It is mandatory to procure user consent prior to running these cookies on your website. Our manufacturers include, but are not limited to Navistar Ford, Dorman, Newstar and Motorcraft. May 24, 2021 #1. 1111 Bad ground to Electronic Control Unit (ECU) or ECU failure-check grounds or replace. Codes may be displayed on either the gauge cluster or an optional vehicle information display (VID). bandwidth). I am getting a 128:F04 SID017_P fault on my 2000 international Data Valid but Above Normal Range, Not available, Data Valid, but Below Normal Range, Not available, Short To Ground or Overload in Air Shield, Private J1939 datalink problem (exceeded The Power Pack E Module has, (PGN 65313 , Byte 4) indicates a value in the range of FCh to FEh, (PGN 65313 , Byte 7) indicates a value of, Motor Has Short or Open or Window is Jammed, Open Circuit in Remote Bunk Start Circuit, Faulty Switch Actuator or Micro switch for, Trailer Left Turn Light Relay 6, Trailer License Plate Light Relay 5, Trailer License Plate Light Relay 6, Trailer Right Turn Light Relay 6, Open Circuit in Trailer Stop Lamp Circuit, Transfer Case Front Driveline 6, Transfer Case Neutral Solenoid 5, Transfer Case Neutral Solenoid 6, Transfer Case PTO Solenoid 5, Transfer Case PTO Solenoid 6, Transfer Case PTO Switch 2, Transfer Case Rear Driveline 6, Transmission PTO Retention 5, Transmission PTO Retention 6, Transmission PTO Switch 2, Two Speed Axle Actuator 5, Mirror Heater 2, Universal Air Solenoid Relay Driver 2 6 Universal Air Solenoid Relay Driver 2 Short To Ground or Defective Solenoid, Universal Air Solenoid Relay Driver 3 5 Universal Air Solenoid Relay Driver 3 Open Circuit or Defective Solenoid, Driver Output Under Current Or Open Circuit, Fault Switch Actuator or Micro switch for, Low Side Driver RD4 Fault is reported when Short to Battery condition is detected, High Side Driver RD31 Fault is reported when Short to Ground condition is Detected, Low Side Driver RD7 Fault is reported when Short to Battery condition is detected, High Side Driver RD32 Fault is reported when Short to Ground condition is Detected, 5) bottom row position 1 from left (Switch 7 of 12), 5) bottom row position 6 from left (Switch 12 of 12), microswitch in location configured as empty, 6) top row position 1 from left (Switch 1 of 12), NEC Service Door Command 6, NEC Service Door Command is Short To Ground or Defective Solenoid Not available, NEC Post Trip Inspection Command Open Circuit or Defective Solenoid Not available, TEM Interlocked Switch Relay 1 5, TEM Switch Interlocked Output Open circuit in TEM Interlocked circuit 1 Not available, TEM Switch Interlocked Output Short circuit in TEM Interlocked circuit 1 Not available, TEM Switch Interlocked Output Open circuit in TEM Interlocked circuit 2 Not available, TEM Switch Interlocked Output Short circuit in TEM Interlocked circuit 2 Not available, Transfer case low indicator high side Not available Not available, Transfer case neutral indicator high Not available Not available, Windshield Heat Left Output 6, Windshield Heat Left Output Short- Short Circuit detected in Windshield Heat Not available, Windshield Heat Right Output Under Open Circuit detected in Windshield Heat Not available, Windshield Heat Right Output Short- Short Circuit detected in Windshield Heat Not available, Left Windshield Heat Temperature Left Windshield Heat Temperature Sensor Not available, Right Windshield Heat Temperature Right Windshield Heat Temperature Not available, Connector J4 Pin E11 has a load on Connector J4 Pin E11 is drawing current Not available, unused configuration and or wiring harness, Relay Driver 17, Channel 9 13, Connector J4 Pin F6 has a load on Connector J4 Pin F6 is drawing current Not available, Connector J4 Pin F7 has a load on Connector J4 Pin F7 is drawing current Not available, Connector J4 Pin F2 has a load on Connector J4 Pin F2 is drawing current Not available, Connector J4 Pin F3 has a load on Connector J4 Pin F3 is drawing current Not available, Connector J4 Pin F1 has a load on Connector J4 Pin F1 is drawing current Not available, Relay Driver 23, Channel 15 13, Connector J4 Pin F4 has a load on Connector J4 Pin F4 is drawing current Not available, this pin that has been configured as unused, and it is configured as unused check configuration and or wiring harness Connector J4 Pin F10 is drawing current, configuration and or wiring harness Connector J4 Pin E3 is drawing current, configuration and or wiring harness Connector J4 Pin E2 is drawing current, configuration and or wiring harness Connector J4 Pin E4 is drawing current, configuration and or wiring harness Connector J4 Pin E8 is drawing current, configuration and or wiring harness Switch actuator installed or bad, I am thinking of purchasing a 2016 international prostar. Fault Code Reference | TruckFaults | Fault Code Diagnostic Source i dont have a scanner but on the dash i have 2 fault codes. Discussion in 'International Forum' started by Capt Dan, Dec 10, 2012. 2 Open all fuel cocks and check that no leakage occurs. Turn the key switch to the ACCESSORY position to view only previously active codes. Is there a particular test that I can request to check for air or a cracked tube? FMI=7 Mechanical System Not Responding Or Out Of Adjustment Open in Ignition Signal Input Circuit To BC, An overcurrent condition in the Vehicle DC, An overcurrent condition in the Vehicle AC, Open Circuit in Power Divider Lock Circuit, Faulty ABS Module or Drivetrain Data Link, Faulty Meritor Wabco Brake Controller Not available, Drivetrain J1939 data link, an improperly, Private J1939 datalink problem (exceeded BC has failed to receive heartbeat, Faulty Switch Actuator or Microswitch for. ECU. 1-5 Months Go to. A&A FREIGHT LLC Bobtail Member. 126. The feature is not password protected to prevent unauthorized access. DISPLAYING DIAGNOSTIC TROUBLE CODES. Cummins ISX Fault code 128: F01 Discussion in 'Ask An Owner Operator' started by A&A FREIGHT LLC, May 24, 2021. The injector for my 6.0 powerstroke was a quality part. 3 Years FMI=16 Data Valid But Above Normal Operating Range Moderately Severe Level Every month 400 people find a job with the help of TruckersReport. International had the truck for 2 weeks and told me they cant find a problem with the truck. NOTE The VID will display Not Available if a DTC description is not available for a particular fault.
